Updated build configs

Config.h

@@ -27,16 +27,6 @@
 	#define MODE_HOST 0x11
 	#define MODE_TNC  0x12
 
-	#if defined(__AVR_ATmega1284P__)
-	    #define PLATFORM PLATFORM_AVR
-	    #define MCU_VARIANT MCU_1284P
-	#elif defined(__AVR_ATmega2560__)
-	    #define PLATFORM PLATFORM_AVR
-	    #define MCU_VARIANT MCU_2560
-	#elif defined(ESP32)
-	    #define PLATFORM PLATFORM_ESP32
-	    #define MCU_VARIANT MCU_ESP32
-
 	#define CABLE_STATE_DISCONNECTED 0x00
 	#define CABLE_STATE_CONNECTED    0x01
 	uint8_t cable_state = CABLE_STATE_DISCONNECTED;
@@ -51,6 +41,16 @@
 	bool bt_ready = false;
 	bool bt_enabled = false;
 	bool bt_allow_pairing = false;
+
+	#if defined(__AVR_ATmega1284P__)
+	    #define PLATFORM PLATFORM_AVR
+	    #define MCU_VARIANT MCU_1284P
+	#elif defined(__AVR_ATmega2560__)
+	    #define PLATFORM PLATFORM_AVR
+	    #define MCU_VARIANT MCU_2560
+	#elif defined(ESP32)
+	    #define PLATFORM PLATFORM_ESP32
+	    #define MCU_VARIANT MCU_ESP32
 	#else
 	    #error "The firmware cannot be compiled for the selected MCU variant"
 	#endif
@@ -60,7 +60,7 @@
 	#define HEADER_L   1
 	#define MIN_L	   1
 
-	#define CMD_L      4
+	#define CMD_L      10
 
 	// MCU dependent configuration parameters
 
@@ -115,19 +115,23 @@
 			const int pin_dio = 39;
 			const int pin_led_rx = 14;
 			const int pin_led_tx = 32;
+            #define HAS_BLUETOOTH true
 		#elif BOARD_MODEL == BOARD_TBEAM
 			const int pin_cs = 18;
 			const int pin_reset = 23;
 			const int pin_dio = 26;
 			const int pin_led_rx = 2;
 			const int pin_led_tx = 4;
+            #define HAS_DISPLAY true
             #define HAS_PMU true
+            #define HAS_BLUETOOTH true
 		#elif BOARD_MODEL == BOARD_HUZZAH32
 			const int pin_cs = 4;
 			const int pin_reset = 36;
 			const int pin_dio = 39;
 			const int pin_led_rx = 14;
 			const int pin_led_tx = 32;
+			#define HAS_BLUETOOTH true
 		#elif BOARD_MODEL == BOARD_LORA32_V2_0
 			const int pin_cs = 18;
 			const int pin_reset = 12;
@@ -166,6 +170,8 @@
 				const int pin_led_rx = 25;
 				const int pin_led_tx = 25;
 			#endif
+			#define HAS_DISPLAY true
+			#define HAS_BLUETOOTH true
 		#elif BOARD_MODEL == BOARD_RNODE_NG_20
 			const int pin_cs = 18;
 			const int pin_reset = 12;

RNode_Firmware.ino

@@ -660,13 +660,14 @@ void serialCallback(uint8_t sbyte) {
             }
             cbuf[frame_len++] = sbyte;
         }
-
+        #if HAS_DISPLAY
           if (frame_len == 9) {
             uint8_t line = cbuf[0];
             if (line > 63) line = 63;
             int fb_o = line*8; 
             memcpy(fb+fb_o, cbuf+1, 8);
           }
+        #endif
     } else if (command == CMD_FB_READ) {
       if (sbyte != 0x00) {
         kiss_indicate_fb();

Utilities.h

@@ -603,7 +603,7 @@ void kiss_indicate_fbstate() {
 			serial_write(0x00);
 		}
 	#else
-		serial_write(0xFF)
+		serial_write(0xFF);
 	#endif
 	serial_write(FEND);
 }
@@ -619,7 +619,7 @@ void kiss_indicate_fb() {
 			serial_write(byte);
 		}
 	#else
-		serial_write(0xFF)
+		serial_write(0xFF);
 	#endif
 	serial_write(FEND);
 }