You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
165 lines
4.9 KiB
165 lines
4.9 KiB
.TH tncattach 8 "September 12, 2020"
|
|
|
|
.SH NAME
|
|
.
|
|
.
|
|
tncattach \- Attach TNC devices as system network interfaces
|
|
|
|
.SH SYNOPSIS
|
|
.
|
|
.
|
|
\f[B]tncattach\f[R] [OPTION...] port baudrate
|
|
|
|
.SH DESCRIPTION
|
|
Attach KISS TNC devices as network interfaces in Linux. This program allows you to attach TNCs or any KISS-compatible device as a network interface. This program does not need any kernel modules, and has no external dependencies outside the standard Linux and GNU C libraries.
|
|
|
|
.SH OPTIONS
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-m, \-\-mtu=MTU
|
|
.
|
|
Specify interface MTU
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-e, \-\-ethernet
|
|
Create a full ethernet device
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-i, \-\-ipv4=IP_ADDRESS
|
|
Configure an IPv4 address on interface
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-n, \-\-noipv6
|
|
Filter IPv6 traffic from reaching TNC
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-\-noup
|
|
Only create interface, don't bring it up
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-T, \-\-kisstcp
|
|
Use KISS over TCP instead of serial port
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-H, \-\-tcphost=TCP_HOST
|
|
Host to connect to when using KISS over TCP
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-P, \-\-tcpport=TCP_PORT
|
|
TCP port when using KISS over TCP
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-t, \-\-interval=SECONDS
|
|
Maximum interval between station identifications
|
|
.
|
|
.
|
|
.TP
|
|
.B \-s, \-\-id=CALLSIGN
|
|
Station identification data
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-d, \-\-daemon
|
|
Run tncattach as a daemon
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-v, \-\-verbose
|
|
Enable verbose output
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-?, \-\-help
|
|
Show help
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-\-usage
|
|
Give a short usage message
|
|
.
|
|
.
|
|
.TP
|
|
.BI \-V, \-\-version
|
|
Print program version
|
|
.
|
|
.
|
|
|
|
.SH USAGE
|
|
The program supports attaching TNCs as point-to-point tunnel devices, or generic ethernet devices. The ethernet mode is suitable for point-to-multipoint setups, and can be enabled with the corresponding command line switch. If you only need point-to-point links, it is advisable to just use the standard point-to-point mode, since it doesn't incur the ethernet header overhead on each packet.
|
|
.P
|
|
If you want to connect to a virtual KISS TNC over a TCP connection, you can use the -T option, along with the -H and -P options to specify the host and port.
|
|
.P
|
|
Additionally, it is worth noting that tncattach can filter out IPv6 packets from reaching the TNC. Most operating systems attempts to autoconfigure IPv6 when an interface is brought up, which results in a substantial amount of IPv6 traffic generated by router solicitations and similar, which is usually unwanted for packet radio links and similar.
|
|
.P
|
|
If you intend to use tncattach on a system with mDNS services enabled (avahi-daemon, for example), you may want to consider modifying your mDNS setup to exclude TNC interfaces, or turning it off entirely, since it will generate a lot of traffic that might be unwanted.
|
|
|
|
.SH STATION IDENTIFICATION
|
|
|
|
You can configure tncattach to automatically transmit station identification beacons according to a given interval, by using the --id and --interval options. Identification will be transmitted as raw data frames with whatever content has been specified in the --id option. Useful for amateur radio use, or other areas where station identification is necessary.
|
|
.P
|
|
Identification beacons will be transmitted when:
|
|
.P
|
|
.IP
|
|
There is outgoing data to send, and the specified interval has elapsed.
|
|
.IP
|
|
The specified interval elapses, and data has been sent since the last ID beacon.
|
|
.IP
|
|
The program exits, if any data frames have been transmitted since the last ID beacon.
|
|
.P
|
|
The above methodology should comply with station identification rules for amateur radio in most parts of the world, and complies with US Part 97 rules.
|
|
|
|
.SH EXAMPLES
|
|
.
|
|
Create an ethernet device with a USB-connected TNC, set the MTU, filter IPv6 traffic, and set an IPv4 address:
|
|
.IP
|
|
sudo tncattach /dev/ttyUSB0 115200 --ethernet --mtu 576 --noipv6 --ipv4 10.92.0.10/24
|
|
.P
|
|
Create an ethernet device with a TCP-connected TNC, set the MTU, filter IPv6 traffic, and set an IPv4 address:
|
|
.IP
|
|
sudo tncattach -T -H localhost -P 8001 --ethernet --mtu 576 --noipv6 --ipv4 10.92.0.10/24
|
|
.P
|
|
You can interact with the interface like any other using the ip or ifconfig utilities.
|
|
.p
|
|
Check interface is running:
|
|
.P
|
|
# ifconfig
|
|
.br
|
|
tnc0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 400
|
|
.br
|
|
inet 10.93.0.1 netmask 255.255.255.255 destination 10.93.0.2
|
|
.br
|
|
unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 500 (UNSPEC)
|
|
.br
|
|
RX packets 0 bytes 0 (0.0 B)
|
|
.br
|
|
RX errors 0 dropped 0 overruns 0 frame 0
|
|
.br
|
|
TX packets 0 bytes 0 (0.0 B)
|
|
.br
|
|
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
|
|
.P
|
|
.SH WORTH KNOWING ON RASPBIAN
|
|
On some versions of Raspbian (and probably other operating systems), the DHCP client daemon dhcpcd interferes with TNC interfaces, by overriding their MTU and trying to auto-configure link-local addresses. You probably don't want this, and it can be disabled by editing the /etc/dhcpcd.conf file, adding a statement telling dhcpcd to ignore your TNC interface:
|
|
.P
|
|
# Add the following statement somewhere at the beginning
|
|
.br
|
|
# of /etc/dhcpcd.conf to prevent dhcpcd from changing MTU
|
|
.br
|
|
denyinterfaces tnc0
|
|
|
|
.SH SEE ALSO
|
|
|
|
rnodeconfigutil(8)
|
|
|
|
.SH AUTHOR
|
|
|
|
Mark Qvist
|
|
|