/*********************************************************************************
 *
 *  weather_station is a weatherstation build around the SparkFun weather meter
 *  It can measure wind speed, wind gust , wind direction, rain fall, temperature,
 *  humidity and air pressure and has an RS-485 ModBus interface for your convenience. 
 *
 *  LED on Arduino gives status:
 *
 *       ON    : Booting
 *       BLINK : I2C ERROR
 *       FLASH : Heartbeat
 *
 * Copyright (C) 2023, 2024 M.T. Konstapel https://meezenest.nl/mees
 *
 * This file is part of weather_station
 *
 *    weather_station is free software: you can redistribute it and/or modify
 *    it under the terms of the GNU General Public License as published by
 *    the Free Software Foundation, either version 3 of the License, or
 *    (at your option) any later version.
 *
 *    weather_station is distributed in the hope that it will be useful,
 *    but WITHOUT ANY WARRANTY; without even the implied warranty of
 *    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *    GNU General Public License for more details.
 *
 *    You should have received a copy of the GNU General Public License
 *    along with weather_station. If not, see <https://www.gnu.org/licenses/>.
 *
 **********************************************************************************/
#include <ModbusSerial.h>
#include "SparkFun_Weather_Meter_Kit_Arduino_Library.h"

//I2C
#include <Wire.h>
#include "i2c.h"

//Temperature and humidity sensor
#include "i2c_SI7021.h"
SI7021 si7021;

// Pressure sensor
#include "i2c_BMP280.h"
BMP280 bmp280;
float PRESSURE_OFFSET = 210;   // Calibration of BMP280: offset in Pascal

/**************************/
/* Configurable variables */
/**************************/
// Sparkfun weather station
int windDirectionPin = A0;
int windSpeedPin = 2;
int rainfallPin = 3;
// RS485 driver
#define RS485_RE 11            // Tight to RS485_DE and must be configured as an input to prevent a short circuit
#define RS485_DE 12
// Used Pins
const int TxenPin = RS485_DE; // -1 disables the feature, change that if you are using an RS485 driver, this pin would be connected to the DE and /RE pins of the driver.
// ModBus address
const byte SlaveId = 14;
/* Modbus Registers Offsets (0-9999)
 *
 * 30000: Weater station ID (0x5758)
 * 30001: Wind direction (degrees)
 * 30002: Wind speed (average over 10 minutes in km/h)
 * 30003: Wind gust (peak wind speed in the last 10 minutes in km/h)
 * 30004: Temperature (degrees Celcius)
 * 30005: Rain last hour (l/m2)
 * 30006: Rain last 24 hours (l/m2)
 * 30007: Rain since midnight (l/m2) [NOT IMPLEMENTED, always 0]
 * 30008: Humidity (percent)
 * 30009: Barometric pressure (hPa)
 * 30010: Luminosity (W/m2)
 * 30011: Snow fall [NOT IMPLEMENTED, always 0]
 * 30012: Raw rainfall counter (mm)
 * 30013: Temperature pressure sensor (degrees Celsius)
 * 30014: Status bits 0=heater, 1-15: reserved
 *
 */
const int SensorIDIreg                = 0;
const int SensorWindDirectionIreg     = 1;
const int SensorWindSpeedIreg         = 2;
const int SensorWindGustIreg          = 3;
const int SensorTemperatureIreg       = 4;
const int SensorRainIreg              = 5;
const int SensorRainLast24Ireg        = 6;
const int SensorRainSinceMidnightIreg = 7;
const int SensorHumidityIreg          = 8;
const int SensorPressureIreg          = 9;
const int SensorLuminosityIreg        = 10;
const int SensorSnowFallIreg          = 11;
const int SensorRainfallRawIreg       = 12;
const int SensorTemperatureBackupIreg = 13;
const int SensorStatusBitsIreg        = 14;

/* Modbus Registers Offsets (0-9999)
 * Coils
 * 0 = Heater algorithm (0 = disable, 1 = enable)
 */
const int HeaterCoil = 0;

// RS-485 serial port 
#define MySerial Serial // define serial port used, Serial most of the time, or Serial1, Serial2 ... if available
const unsigned long Baudrate = 9600;
/******************************/
/* END Configurable variables */
/******************************/

// Create an instance of the weather meter kit
SFEWeatherMeterKit weatherMeterKit(windDirectionPin, windSpeedPin, rainfallPin);

// ModbusSerial object
ModbusSerial mb (MySerial, SlaveId, TxenPin);

unsigned long ts;
unsigned long HourTimer;
int WindGustData1[30];
unsigned char WindGustData1Counter=0;
int WindGustData2[10];
unsigned char WindGustData2Counter=0;
int WindAverageData1[30];
unsigned char WindAverageData1Counter=0;
int WindAverageData2[10];
unsigned char WindAverageData2Counter=0;
int RainPerHour[24];
unsigned char RainPerHourCounter=0;

struct MeasuredData {
  int WindDirection;
  int WindSpeed;
  int WindGust;
  int Rain;
  int RainLast24;
  int SensorRainSinceMidnight;
  int Pressure;
  int Luminosity;
  int StatusBits = 0;
  unsigned int RainfallCounter = 0;

  float Temperature;
  float Humidity;
  float TemperatureBackup;

  bool HeaterStatus = 0;
} MeasuredData;

// State machine implementing smart heater to prevent saturation of the sensor
char HeaterSi7021 (float humidity)
{
  static int state=0;
  static unsigned long StatemachineTimer=0;
  bool TempValid=1;
  bool Heater=0;

  // If Smart heater algorithm is disabled, reset the statemachine forever.
  // TempValid bit is also forced to 1, but it could be that we just came out of a heater period.
  // We assume that the client on the other side of the ModBus is smart enough to understand.
  if (MeasuredData.StatusBits & 0x04)
    state = 0;

  switch (state)
  {
    // Default state: humidity is below 95%
    case 0:
      Heater = 0;
      if (humidity >= 95) {
        StatemachineTimer = millis();
        state = 1;
      }
      break;
    // Humidity went above 95%. See if humidity stays above 95% for more than an hour, if so turn on heater
    case 1:
      if (humidity >= 95) {
        if ( (millis() - StatemachineTimer) >= 3.6e+6 ) {
          Heater = 1;
          TempValid = 0;
          StatemachineTimer = millis();
          state = 2;
        } else {
          Heater = 0;
        }
      } else {
        Heater = 0;
        state = 0;
      }      
      break;

    // Heater is now on, let the sensor cook for 10 minutes
    case 2:
      if ( (millis() - StatemachineTimer) >= 600000 ) {
        StatemachineTimer = millis();
        Heater = 0;
        state = 3;
      } else {
        Heater = 1;
      }
      TempValid = 0;
      break;
    // Heater is now off, let the sensor cool for 10 minutes
    case 3:
      if ( (millis() - StatemachineTimer) >= 600000 ) {
        TempValid = 1;            // Sensor cooled, so we can take a valid temperature reading
        if (humidity >= 95) {
          // Humidity still above 95%, repeat heating/cooling
          Heater = 1;
          StatemachineTimer = millis();
          state = 2;
        } else {
          // Humidity below 95%, reset statemachine
          Heater = 0;
          state = 0;
        }
      } else {
        Heater = 0;
        TempValid = 0;
      }
      break;

    default:
      Heater = 0;
      state = 0;
      break;
  }

  return TempValid<<1 | Heater;

}
// Read Si7021 sensor and process data
void ReadSi7021 (void)
{
    char result=0x2;

    si7021.triggerMeasurement();
    si7021.getHumidity(MeasuredData.Humidity);

    if (MeasuredData.Humidity>100 || MeasuredData.Humidity<0)
      MeasuredData.Humidity = 100;
 
    //If humidity is larger than 95% switch on heater to get more acurate measurement and prevent memory offset
    result = HeaterSi7021(MeasuredData.Humidity);
    MeasuredData.StatusBits &= 0xFFFC;  // Reset heater status bits to zero
    MeasuredData.StatusBits |= result;  // And set the proper bits to one if there are any. The result is we copied the status bits to the register
  
    // Scale for more decimal positions when converted to integer value for ModBus
    MeasuredData.Humidity *= 100;

    // Temperture readings are valid (as the sensor is not heated)
    if (result & 0x2) {
      si7021.getTemperature(MeasuredData.Temperature);
      // Scale for more decimal positions when converted to integer value for ModBus
      MeasuredData.Temperature *= 100;
      //Serial.print(F("Valid temp"));
    }
    // Statemachine thinks it is time to switch on the heater
    if (result & 0x1) {
      //Serial.print(F("Heater on."));
      MeasuredData.HeaterStatus = 1;
      
    } else {
      //Serial.print(F("Heater off."));
      MeasuredData.HeaterStatus = 0;
    }
    si7021.setHeater(MeasuredData.HeaterStatus);

}

// Read BMP280
void ReadBMP280 (void)
{
  bmp280.awaitMeasurement();

  float pascal;
  bmp280.getPressure(pascal);
  pascal = (pascal - PRESSURE_OFFSET) / 10;  // Convert to hPa
  MeasuredData.Pressure = pascal;

  bmp280.getTemperature(MeasuredData.TemperatureBackup);
  // Scale for more decimal positions when converted to integer value for ModBus
  MeasuredData.TemperatureBackup *= 100;
  
  bmp280.triggerMeasurement();

}

int MaxOfArray (int array[], unsigned int length)
{
  int maximum_value = 0;
  
  while (length--)
  {
    if (array[length] > maximum_value)
      maximum_value = array[length];
  }
  return maximum_value;
}

int AverageOfArray (int array[], unsigned int length)
{
  int tmp_value = 0;
  unsigned char tmp_length = length;
  int average_value = 0;
 
  while (length--)
  {
    tmp_value += array[length];
  }
  average_value = tmp_value/tmp_length;

  return average_value;
}

// Call this function every 2 seconds
void ReadSparkfunWeatherStation (void)
{
  unsigned char cnt=0;

  float tmpRegister;

  tmpRegister = 10*weatherMeterKit.getWindDirection();  // Use float for conversion to degrees times 10, than put it in integer register for ModBus
  MeasuredData.WindDirection = tmpRegister;
  tmpRegister = 100*(weatherMeterKit.getWindSpeed())/3.6;  // Use float for conversion to m/s times 100, than put it in integer register for ModBus
  MeasuredData.WindSpeed = tmpRegister;
  tmpRegister = 100*weatherMeterKit.getTotalRainfall();    // Use float for conversion to l/m2 times 100, than put it in integer register for ModBus
  MeasuredData.Rain = tmpRegister;

  // FIFO for calculating wind gust of last 10 minutes
  // to preserve valuable RAM we caanot store all measurements of the last 10 minutes.
  // So we use a hack: store the last 30 values in a FIFO and every minute we store the maximum value from this FIFO in another FIFO.
  // This second FIFO is 10 deep: it stores the maximum values of the last 10 minutes.
  // The maximum value from this FIFO is the maximum wind gust of the last 10 minutes.
  if ( WindGustData1Counter < 29 )
  {
    WindGustData1Counter++;
  }
  else
  {
    if ( WindGustData2Counter < 9 )
    {
      WindGustData2Counter++;
    }
    else
    {
      WindGustData2Counter=0;
    }
    WindGustData2[WindGustData2Counter] = MaxOfArray(WindGustData1, 30);
    WindGustData1Counter=0;
  }
  WindGustData1[WindGustData1Counter] = MeasuredData.WindSpeed;
  MeasuredData.WindGust= MaxOfArray(WindGustData2, 10);

  // Smart FIFO, same as for Wind Gust, but now for average wind speed over 10 minutes
  if ( WindAverageData1Counter < 29 )
  {
    WindAverageData1Counter++;
  }
  else
  {
    if ( WindAverageData2Counter < 9 )
    {
       WindAverageData2Counter++;
    }
    else
    {
      WindAverageData2Counter=0;
    }
    WindAverageData2[WindAverageData2Counter] = AverageOfArray(WindAverageData1, 30);
    WindAverageData1Counter=0;
    WindAverageData1[WindAverageData1Counter] = MeasuredData.WindSpeed;
  }
  WindAverageData1[WindAverageData1Counter] = MeasuredData.WindSpeed;
  MeasuredData.WindSpeed = AverageOfArray(WindAverageData2, 10);

  // Record rainfall in one hour, save last 24 readings in FIFO
  if ( ( millis() - HourTimer) >= 3.6e+6) {
    
    HourTimer = millis();

    if ( RainPerHourCounter < 23 )
    {
      RainPerHourCounter++;
    } else {
      RainPerHourCounter=0;
    }
    RainPerHour[RainPerHourCounter] = MeasuredData.Rain;
    // Every time before we reset the TotalRainCounter we add the amount to the RawRainCounter.
    // This 16 bit register will eventually overflow, but 655.35mm of rain fall is a lot!
    MeasuredData.RainfallCounter += MeasuredData.Rain;  // We don't care about the rounding error due to the convertion from float to int
    weatherMeterKit.resetTotalRainfall();

    // Calculate rain fall in the last 24 hours
    MeasuredData.RainLast24=0;
    for (cnt=0; cnt<24;cnt++) {
      MeasuredData.RainLast24 += RainPerHour[cnt];
    }

  }
  MeasuredData.Rain = RainPerHour[RainPerHourCounter];
}

void setup() {

  MySerial.begin (Baudrate); // works on all boards but the configuration is 8N1 which is incompatible with the MODBUS standard
  // prefer the line below instead if possible
  // MySerial.begin (Baudrate, MB_PARITY_EVEN);

  // initialize digital pin LED_BUILTIN as an output and turn it on.
  pinMode(LED_BUILTIN, OUTPUT);
  digitalWrite(LED_BUILTIN, HIGH);

  //Setup control lines for RS485 driver
  pinMode(RS485_RE,INPUT);        // In hardware connected to RS485_DE. Should be input to prevent a short circuit!
  pinMode(RS485_DE,OUTPUT);
  digitalWrite(RS485_DE,LOW);

  mb.config (Baudrate);
  mb.setAdditionalServerData ("TEMP_SENSOR"); // for Report Server ID function (0x11)

  // Add SensorIreg registers - Use addIreg() for analog Inputs
  mb.addIreg (SensorIDIreg);
  mb.addIreg (SensorWindDirectionIreg);
  mb.addIreg (SensorWindSpeedIreg);
  mb.addIreg (SensorWindGustIreg);
  mb.addIreg (SensorTemperatureIreg);
  mb.addIreg (SensorRainIreg);
  mb.addIreg (SensorRainLast24Ireg);
  mb.addIreg (SensorRainSinceMidnightIreg);
  mb.addIreg (SensorHumidityIreg);
  mb.addIreg (SensorPressureIreg);
  mb.addIreg (SensorLuminosityIreg);
  mb.addIreg (SensorSnowFallIreg);
  mb.addIreg (SensorRainfallRawIreg);
  mb.addIreg (SensorTemperatureBackupIreg);
  mb.addIreg (SensorStatusBitsIreg);

  // Add HeaterCoil register
  mb.addCoil (HeaterCoil);
    
  // Set Weather station ID
  mb.Ireg (SensorIDIreg, 0x5758);
  // Set unused register to zero
  mb.Ireg (SensorRainSinceMidnightIreg, 0);
  mb.Ireg (SensorSnowFallIreg, 0);
 
  Serial.println(F("Weather station v0.2.1"));
  Serial.println(F("(C)2024 M.T. Konstapel"));
  Serial.println(F("This project is free and open source"));
  Serial.println(F("More details: https://meezenest.nl/mees/"));

  //Initialize Si7021 sensor
  Serial.print(F("Humidity sensor SI7021 "));
  if (si7021.initialize())
    Serial.println(F("found"));
  else
  {
    Serial.println(F("missing"));
    while(1) {
      digitalWrite(LED_BUILTIN, HIGH);  // turn the LED on (HIGH is the voltage level)
      delay(500);                      // wait for half a second
      digitalWrite(LED_BUILTIN, LOW);   // turn the LED off by making the voltage LOW
      delay(500);  
    }
  }

  // The standard library of the Si7021 sets the heater element to the default 3.1mA, but we want the full power
  // We could alter the library, but than we break compatibility. So for this one time we do a raw-write to the 
  // heater register.
  const uint8_t SI7021_I2C_ADDRESS 		              =(0x40);
  const uint8_t SI7021_CMD_WRITE_HEATER_CONTROL_REG =(0x51);
  const uint8_t SI7021_HEATER_FULL_BLAST            =(0x0F); // Set heater to 94mA
  i2c.writeByte(SI7021_I2C_ADDRESS, SI7021_CMD_WRITE_HEATER_CONTROL_REG, SI7021_HEATER_FULL_BLAST);

  // Initialize BMP280 pressure sensor
  Serial.print(F("Pressure sensor BMP280 "));
  if (bmp280.initialize())   
    Serial.println(F("found"));
  else
  {
    Serial.println(F("missing"));
    while(1) {
      digitalWrite(LED_BUILTIN, HIGH);  // turn the LED on (HIGH is the voltage level)
      delay(500);                      // wait for half a second
      digitalWrite(LED_BUILTIN, LOW);   // turn the LED off by making the voltage LOW
      delay(500);  
    }
  }

  // onetime-measure:
  bmp280.setEnabled(0);
  bmp280.triggerMeasurement();

    // Expected ADC values have been defined for various platforms in the
    // library, however your platform may not be included. This code will check
    // if that's the case
#ifdef SFE_WMK_PLAFTORM_UNKNOWN
    // The platform you're using hasn't been added to the library, so the
    // expected ADC values have been calculated assuming a 10k pullup resistor
    // and a perfectly linear 16-bit ADC. Your ADC likely has a different
    // resolution, so you'll need to specify it here:
    weatherMeterKit.setADCResolutionBits(10);
#endif

  // Here we create a struct to hold all the calibration parameters
  SFEWeatherMeterKitCalibrationParams calibrationParams = weatherMeterKit.getCalibrationParams();
  
  // The wind vane has 8 switches, but 2 could close at the same time, which
  // results in 16 possible positions. Each position has a resistor connected
  // to GND, so this library assumes a voltage divider is created by adding
  // another resistor to VCC. Some of the wind vane resistor values are
  // fairly close to each other, meaning an accurate ADC is required. However
  // some ADCs have a non-linear behavior that causes this measurement to be
  // inaccurate. To account for this, the vane resistor values can be manually
  // changed here to compensate for the non-linear behavior of the ADC
  calibrationParams.vaneADCValues[WMK_ANGLE_0_0]   = 943;
  calibrationParams.vaneADCValues[WMK_ANGLE_22_5]  = 828;
  calibrationParams.vaneADCValues[WMK_ANGLE_45_0]  = 885;
  calibrationParams.vaneADCValues[WMK_ANGLE_67_5]  = 702;
  calibrationParams.vaneADCValues[WMK_ANGLE_90_0]  = 785;
  calibrationParams.vaneADCValues[WMK_ANGLE_112_5] = 404;
  calibrationParams.vaneADCValues[WMK_ANGLE_135_0] = 460;
  calibrationParams.vaneADCValues[WMK_ANGLE_157_5] = 82;
  calibrationParams.vaneADCValues[WMK_ANGLE_180_0] = 91;
  calibrationParams.vaneADCValues[WMK_ANGLE_202_5] = 64;
  calibrationParams.vaneADCValues[WMK_ANGLE_225_0] = 185;
  calibrationParams.vaneADCValues[WMK_ANGLE_247_5] = 125;
  calibrationParams.vaneADCValues[WMK_ANGLE_270_0] = 285;
  calibrationParams.vaneADCValues[WMK_ANGLE_292_5] = 242;
  calibrationParams.vaneADCValues[WMK_ANGLE_315_0] = 628;
  calibrationParams.vaneADCValues[WMK_ANGLE_337_5] = 598;

  // The rainfall detector contains a small cup that collects rain water. When
  // the cup fills, the water is dumped and the total rainfall is incremented
  // by some value. This value defaults to 0.2794mm of rain per count, as
  // specified by the datasheet
  calibrationParams.mmPerRainfallCount = 0.2794;

  // The rainfall detector switch can sometimes bounce, causing multiple extra
  // triggers. This input is debounced by ignoring extra triggers within a
  // time window, which defaults to 100ms
  calibrationParams.minMillisPerRainfall = 100;

  // The anemometer contains a switch that opens and closes as it spins. The
  // rate at which the switch closes depends on the wind speed. The datasheet
  // states that a wind of 2.4kph causes the switch to close once per second
  calibrationParams.kphPerCountPerSec = 2.4;

  // Because the anemometer generates discrete pulses as it rotates, it's not
  // possible to measure the wind speed exactly at any point in time. A filter
  // is implemented in the library that averages the wind speed over a certain
  // time period, which defaults to 1 second. Longer intervals result in more
  // accurate measurements, but cause delay in the measurement
  calibrationParams.windSpeedMeasurementPeriodMillis = 1000;

  // Now we can set all the calibration parameters at once
  weatherMeterKit.setCalibrationParams(calibrationParams);
  
  // Begin weather meter kit
  weatherMeterKit.begin();

  ts = millis();
  RainPerHourCounter = ts;
}

void loop() {

  // Call once inside loop() - all magic here
  mb.task();
  
  // Read each two seconds
  if ( ( millis() - ts) >= 2000) {
    
    ts = millis();

    digitalWrite(LED_BUILTIN, HIGH);  // LED as heartbeat

    // Read temperature and humidity
    ReadSi7021();

    // Read pressure and temperature
    ReadBMP280();

    // Read Wind and rain
    ReadSparkfunWeatherStation();

    // Setting Sparkfun weather station registers
    mb.Ireg (SensorWindDirectionIreg, MeasuredData.WindDirection);
    mb.Ireg (SensorWindSpeedIreg, MeasuredData.WindSpeed);
    mb.Ireg (SensorWindGustIreg, MeasuredData.WindGust);
    mb.Ireg (SensorRainIreg, MeasuredData.Rain);
    mb.Ireg (SensorRainLast24Ireg, MeasuredData.RainLast24);
    mb.Ireg (SensorTemperatureIreg, MeasuredData.Temperature);
    mb.Ireg (SensorHumidityIreg, MeasuredData.Humidity);
    mb.Ireg (SensorPressureIreg, MeasuredData.Pressure);
    mb.Ireg (SensorTemperatureBackupIreg, MeasuredData.TemperatureBackup);
    mb.Ireg (SensorLuminosityIreg, MeasuredData.Luminosity);
    mb.Ireg (SensorRainfallRawIreg, MeasuredData.RainfallCounter);
    mb.Ireg (SensorStatusBitsIreg, MeasuredData.StatusBits);

    // Debug wind vane
    //Serial.print(F("\n    Measured ADC: "));
    //Serial.print(analogRead(windDirectionPin));

    // enable or disable smart heater
    if (mb.Coil (HeaterCoil)) {
      MeasuredData.StatusBits |= 0x04;  // Set bit
    } else {
      MeasuredData.StatusBits &= 0x0B;  // Reset bit
    }

    digitalWrite(LED_BUILTIN, LOW);  // LED as heartbeat


    }
}