Added NeoPixel intensity control

Framing.h

@@ -54,6 +54,8 @@
   #define CMD_FB_READL    0x44
   #define CMD_DISP_INT    0x45
   #define CMD_DISP_ADDR   0x63
+  #define CMD_DISP_BLNK   0x64
+  #define CMD_NP_INT      0x65
   #define CMD_BT_CTRL     0x46
   #define CMD_BT_PIN      0x62
 

RNode_Firmware.ino

@@ -78,6 +78,10 @@ void setup() {
 
   Serial.begin(serial_baudrate);
 
+  #if HAS_NP
+    led_init();
+  #endif
+
   #if BOARD_MODEL != BOARD_RAK4631 && BOARD_MODEL != BOARD_RNODE_NG_22
   // Some boards need to wait until the hardware UART is set up before booting
   // the full firmware. In the case of the RAK4631, the line below will wait
@@ -962,6 +966,40 @@ void serialCallback(uint8_t sbyte) {
             da_conf_save(display_addr);
         }
 
+      #endif
+    } else if (command == CMD_DISP_BLNK) {
+      #if HAS_NP
+        if (sbyte == FESC) {
+            ESCAPE = true;
+        } else {
+            if (ESCAPE) {
+                if (sbyte == TFEND) sbyte = FEND;
+                if (sbyte == TFESC) sbyte = FESC;
+                ESCAPE = false;
+            }
+            if (sbyte == 0x00) {
+              db_conf_save(0x00);
+            } else {
+              db_conf_save(0x01);
+            }
+        }
+
+      #endif
+    } else if (command == CMD_NP_INT) {
+      #if HAS_NP
+        if (sbyte == FESC) {
+            ESCAPE = true;
+        } else {
+            if (ESCAPE) {
+                if (sbyte == TFEND) sbyte = FEND;
+                if (sbyte == TFESC) sbyte = FESC;
+                ESCAPE = false;
+            }
+            npi = sbyte;
+            led_set_intensity(npi);
+            np_int_conf_save(npi);
+        }
+
       #endif
     }
   }

ROM.h

@@ -74,6 +74,9 @@
 	#define ADDR_CONF_DSET 0xB1
 	#define ADDR_CONF_DINT 0xB2
 	#define ADDR_CONF_DADR 0xB3
+	#define ADDR_CONF_DBLK 0xB4
+	#define ADDR_CONF_PSET 0xB5
+	#define ADDR_CONF_PINT 0xB6
 
 	#define INFO_LOCK_BYTE 0x73
 	#define CONF_OK_BYTE   0x73

Utilities.h

@@ -109,7 +109,19 @@ uint8_t boot_vector = 0x00;
 	uint8_t npr = 0;
   uint8_t npg = 0;
   uint8_t npb = 0;
+  float npi = NP_M;
   bool pixels_started = false;
+
+  void led_set_intensity(uint8_t intensity) {
+  	npi = (float)intensity/255.0;
+  }
+
+  void led_init() {
+  	if (EEPROM.read(eeprom_addr(ADDR_CONF_PSET)) != 0xFF) {
+  		led_set_intensity(EEPROM.read(eeprom_addr(ADDR_CONF_PINT)));
+  	}
+  }
+
   void npset(uint8_t r, uint8_t g, uint8_t b) {
   	if (pixels_started != true) {
   		pixels.begin();
@@ -118,7 +130,7 @@ uint8_t boot_vector = 0x00;
 
   	if (r != npr || g != npg || b != npb) {
   		npr = r; npg = g; npb = b;
-  		pixels.setPixelColor(0, pixels.Color(npr*NP_M, npg*NP_M, npb*NP_M));
+  		pixels.setPixelColor(0, pixels.Color(npr*npi, npg*npi, npb*npi));
   		pixels.show();
   	}
   }
@@ -1425,6 +1437,16 @@ void da_conf_save(uint8_t dadr) {
 	eeprom_update(eeprom_addr(ADDR_CONF_DADR), dadr);
 }
 
+void db_conf_save(uint8_t val) {
+	eeprom_update(eeprom_addr(ADDR_CONF_DBLK), val);
+}
+
+void np_int_conf_save(uint8_t p_int) {
+	eeprom_update(eeprom_addr(ADDR_CONF_PSET), 0x01);
+	eeprom_update(eeprom_addr(ADDR_CONF_PINT), p_int);
+}
+
+
 bool eeprom_have_conf() {
     #if HAS_EEPROM
 	    if (EEPROM.read(eeprom_addr(ADDR_CONF_OK)) == CONF_OK_BYTE) {