HOWTO updated

Documentation/HOWTO-change-firmware-and-compile-it_MeesElectronics.md

@@ -121,15 +121,17 @@ If we want to add support for a new board we have to add a new section for this
 
 Let's say we want to add support for the Waveshare ESP32-S3 Pico with an SX1278 LoRa transceiver. First we have to make define both BOARD_MODEL and BOARD_VARIANT. Let's define BOARD_MODEL as 0x61 and BOARD_VARIANT as 0x31 as these numbers are not used yet. Here the 0x31 indicates the use of a SX1278 LoRa transceiver. In the future we can define more transceivers for this board. Then we make entries in the Makefile.
 
-    firmware-waveshare-esp32-s3-pico:
+    # Added board from Mees Electronics
-	    arduino-cli compile --fqbn "esp32:esp32:esp32s3:CDCOnBoot=cdc" $(COMMON_BUILD_FLAGS) --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x61\" \"-DBOARD_VARIANT=0x31\""
+    firmware-waveshare-esp32-s3-pico: check_bt_buffers
+	    arduino-cli compile --fqbn "esp32:esp32:esp32s3:CDCOnBoot=cdc" $(COMMON_BUILD_FLAGS) --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x61\""
 
+    # Added board from Mees Electronics
     upload-waveshare-esp32-s3-pico:
 	    arduino-cli upload -p $(or $(port), /dev/ttyACM0) --fqbn esp32:esp32:esp32s3
 	    @sleep 1
-	    rnodeconf $(or $(port), /dev/ttyACM0) --firmware-hash $$(./partition_hashes ./build/esp32.esp32.waveshare-esp32-s3-pico/RNode_Firmware_CE.ino.bin)
+	    rnodeconf $(or $(port), /dev/ttyACM0) --firmware-hash $$(./partition_hashes ./build/esp32.esp32.esp32s3/RNode_Firmware_CE.ino.bin)
 	    @sleep 3
-	    python ./Release/esptool/esptool.py --port $(or $(port), /dev/ttyACM0) --chip esp32-s3 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
+	    python3 ./Release/esptool/esptool.py --port $(or $(port), /dev/ttyACM0) --chip esp32-s3 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
 
     release-waveshare-esp32-s3-pico:
         arduino-cli compile --fqbn "esp32:esp32:esp32s3:CDCOnBoot=cdc" $(COMMON_BUILD_FLAGS) --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x61\" \"-DBOARD_VARIANT=0x31\""
@@ -143,74 +145,58 @@ Let's say we want to add support for the Waveshare ESP32-S3 Pico with an SX1278
 In the file Boards.h make an entry for the new board within the '#if MCU_VARIANT == MCU_ESP32':
 
     #elif BOARD_MODEL == BOARD_WAVESHARE_ESP32_S3_PICO
-      #define HAS_DISPLAY true
+      #define IS_ESP32S3 true
-      #define DISPLAY OLED
+      #define HAS_DISPLAY false
-      #define HAS_BLUETOOTH true
+      #define HAS_BLUETOOTH false
+      #define HAS_BLE true
       #define HAS_PMU true
       #define HAS_CONSOLE true
       #define HAS_EEPROM true
+      //#define HAS_INPUT true
+      //#define HAS_SLEEP true
+      //#define PIN_WAKEUP GPIO_NUM_0
+      //#define WAKEUP_LEVEL 0
       #define INTERFACE_COUNT 1
+      #define OCP_TUNED 0x38
 
-      const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
+      const int pin_btn_usr1 = 0;
-      #if HAS_TCXO == true
+
-        const bool interface_cfg[INTERFACE_COUNT][3] = {
+      #define HAS_NP true
-                        // SX127X
+      const int pin_np = 21;
-              {
+      #if HAS_NP == false
-                  true, // DEFAULT_SPI
+        #if defined(EXTERNAL_LEDS)
-                  true, // HAS_TCXO
+          const int pin_led_rx = 16;
-                  false  // DIO2_AS_RF_SWITCH
+          const int pin_led_tx = 17;
-              },
+        #else
-        };
+          const int pin_led_rx = 21;
-      const int8_t interface_pins[INTERFACE_COUNT][10] = {
+          const int pin_led_tx = 21;
-                  // SX127X
+        #endif
-          {
-              18, // pin_ss
-              -1, // pin_sclk
-              -1, // pin_mosi
-              -1, // pin_miso
-              -1, // pin_busy
-              26, // pin_dio
-              23, // pin_reset
-              -1, // pin_txen
-              -1, // pin_rxen
-              33  // pin_tcxo_enable
-          }
-      };
-      #endif
-      #if defined(EXTERNAL_LEDS)
-        const int pin_led_rx = 15;
-        const int pin_led_tx = 4;
-      #else
-        const int pin_led_rx = 25;
-        const int pin_led_tx = 25;
       #endif
 
-      #if HAS_TCXO == false
+      const uint8_t interfaces[INTERFACE_COUNT] = {SX1278};
       const bool interface_cfg[INTERFACE_COUNT][3] = {
-                    // SX127X
+                    // SX1278
           {
-              true, // DEFAULT_SPI
+              false, // DEFAULT_SPI
               false, // HAS_TCXO
               false  // DIO2_AS_RF_SWITCH
           },
       };
-
+      const uint8_t interface_pins[INTERFACE_COUNT][10] = {
-      const int8_t interface_pins[INTERFACE_COUNT][10] = {
+                  // SX1278
-                  // SX127X
           {
-              18, // pin_ss
+               10, // pin_ss
-              -1, // pin_sclk
+               12, // pin_sclk
-              -1, // pin_mosi
+               11, // pin_mosi
-              -1, // pin_miso
+               13, // pin_miso
               -1, // pin_busy
-              26, // pin_dio
+              15, // pin_dio
-              23, // pin_reset
+               14, // pin_reset
               -1, // pin_txen
               -1, // pin_rxen
               -1  // pin_tcxo_enable
           }
       };
-      #endif
 
 Also, in the file Utilities.h add entry. Again, within the '#if MCU_VARIANT == MCU_ESP32'.
 
@@ -245,4 +231,4 @@ This will end with error 'This device has not been provisioned yet, cannot set f
 When the rnode is flashed, it is signed with a key. If you conect the rnode to another system, this key cannot be validated. It is possible to write a new key to the rnode by erasing the eeprom and writing the local key to it.
 
     $ rnodeconf /dev/ttyACM0 --eeprom-wipe
-    $ rnodeconf /dev/ttyACM0 -r --platform ESP32 --model a9 --product f0 --hwrev 3
+    $ rnodeconf /dev/ttyACM0 -r --platform ESP32 --model a4 --product f0 --hwrev 3